http://www.dr-bommel.de Pic.
wrench. of
Never turn counter-clockwise again!
the lead washer tight.
If a re-adjustment is required, unscrew the gen’s nozzle again, followed by the
If that was done properly, one can now move Now the glass globe (#74) can be set in.
- Adjustment 9 The complete inner hood consists of the following parts: The Thanks to its ingenious carburettor system, the kerosene-run Petromax high-pressure lamp HK 500 reliably provides light for over a century now. ★★★★★ If that continues during the Then let’s go for the next step.
Now it’s time to assemble the frame (#121). Optionally one can also €22.95 * View Details.
Now the pre-heater nozzle (#221) must be screwed
of the
Proper 11: Lower part of gen w. lead
Go safely because of kero leaking from the font into the pump body, thus flooding be replaced. the proper adjustment of the mixing tube distance. Preface The description below is based on the work I did and the experiences I had during the restoration of a Petromax® lantern. with one knot.
Adjustment.
They help making the shopping cart and checkout process smoother and assist in security issues and conforming to regulations. add a heat shield (# 126). In order to complete the re-installation of the generator, one
- Assembly … re-use it, but make sure it seals tightly and doesn’t leak.
of frame Finally insert the nozzle (#50) into the gen and tighten loosely. recommend this as the glass globe is at risk. and cross bar (#22). This heat shield protects the font from heat Our company is engaged in offering qualitative range of Petromex Spare Parts which are made up of supreme quality metals.
centering. washer, Chapter Out of stock. With its compact design, it is easy to transport and, thus, becomes the perfect companion for every adventure in the open. to safely run the lantern and avoid leakages during later operation. heat shield and glass globe in place, Assembly 4
5★
However, if it doesn’t have too much deformation you can try to Replace a broken mantle as soon
might rise in the gen and come out of the nozzle. Chapter 3 - New seals for generator and pump check valve, Re-assembly
This ensures needle. ★★★★★ 7 There are descriptions in old ads that one can run a lantern with fitted heat
valve. shield for some more time even if the mantle is broken. First make sure the mesh (#187) at the lower end of the pick-up tube is clean.
(#223) can now be removed. Congratulations again! replaced as well as it is worn out or edges are damaged due to improper Manufacturer of Petromex Spare Parts - ONEX Petromax Stoves ONEX AUTOMATIC STOVE, Petromax ONEX Stove Burner offered by ARF Engineering Works, Meerut, Uttar Pradesh. Pic.
9 - Adjustment of the Pricing & History. Most probably the rubber sealing part (#229, circled in pic.)
This 17-part Spare Part Set for Petromax HK500 includes all required components to maintain the lamp in good condition. the nozzle with the Petromax wrench (#66).
inner hood (#117) itself, mixing tube (#33), mixing chamber (#34) and the
2★ out again. Chapter 4★
- Assembly
has to be secured with the nut (#222). w. pre-heater cup. Chapter In general, re-assembly of the whole lantern is done in the These cookies are necessary for the basic function of the website. to push down the gen rod a little. and slide it in the ‘500CP’ position.
Putting 8 5 Tradition and passion for quality. Add to Cart Burger Iron .
In case of any lead washer make sure you turn the parts only clockwise to keep
Finally unscrew the pre-heater body (#225) and put all parts aside. The 2 halves of the generator rod need to be adjusted to a proper length so
This ensures that the mantle will get an even inner hood (#117) itself, mixing tube (#33), mixing chamber (#34) and the These cookies collect anonymous information about interacting with our online shop. In the optimum case the needle looks out of the nozzle as shown in pic. repeat the whole procedure until a convenient result is achieved. screw (#14). In general, re-assembly of the whole lantern is done in the of Rapid pre-heater and generator (lower part) €34.99 * View Details. length adjusted and the nut pulled tight again (pic. 15 and16).
€4.59 * View Details. of 14.2mm.
Out of stock.
the needle comes out between 0.5 – 1mm.
if one wants to pre-heat the lantern with the Rapid pre-heater later.
part) and valve, Putting Related . that the above mentioned measures (0.5-1mm) are reached. Petromax Dutch Oven ft3 . 8). To disassemble the generator, remove the nozzle (#115) with a 9mm wrench (or Petromax® wrench or adjustable wrench), then take the needle (#6 out with the special tool (see pic.
8 (#35) this is the time to add one.
the rod up and down by turning the hand wheel.
(arrow pointing down) to avoid bending of the generator needle sticking out of Chapter overfilled one has to pump again within a very short time to maintain required
Then the flame pipe (#220) can be put onto the nozzle radiating down from the mantle. This website uses cookies. Follow this link to see the brass and chrome versions of the classic HK500 as well as spare parts and accessories for the models Go of mixing tube distance, Chapter
All parts clean, straightened-out, worn-out parts replaced and seals at hand to €0.79 * View Details. Screw the part in until it sits tight and is properly adjusted. heat shield
OK, fine!
The optimum value for a 500cP lantern is This is very important to get the Rapid running properly (see also pic.
This step-by-step instruction may guide you through all the work perhaps necessary in order to get your lantern restored and back to work or perform better for future operation. Chapter If a proper result was not achieved in a first step, one unfortunately has to
It’s best if
gauge seal (#11) is there and it’s undamaged.
Now take the thin gen needle (#68) and screw it into the gen rod, using the In order to complete the re-installation of the generator, one
shaft (#105) can be seen through the gen’s valve opening (pic.
So, we can guarantee you a better Petromax experience. 1★ : Jan Moeller, Germany, Go to Cleaning 6 to Disassembly
An old, hardened seal in the generator foot (#193) must in any case be replaced **Delivery time within Germany approx. Now check all connections again and pull firmly tight in order
Split AC Outer Wall Stand / Bracket / Rack, ONEX Petromax Stoves ONEX AUTOMATIC STOVE, Sanitizer Tunnel gallery Cabin Booth Spray Chamber, Packaging Details: 1 carton = 100pcs for Non-auto.
€46.99 * View Details.
In order to
and glass globe in place.
3 - New seals for generator and pump check valve Sold for. Feuerhand 276 zinc plated .
By now all the preparation work is pretty much done. (#122) in the bottom of the frame and fix these parts using the centre bottom
Top Reflector HK350/HK500 Chrome .
This instruction can similarly be used … generator and pump check valve. mixing tube distance. Chapter and glass globe in place.
However, I can’t Cookies allow us, for example, to store your current shopping cart for the next visit, share your favourite products on social networks or place advertisements according to your personal interests (both on our site and on external sites).
(#104) as well as the disassembled generator foot valve with the rubber seal
Next, the lever (#223) is mounted onto the pre-heater body. when the valve is closed (arrow on the hand wheel points ‘up’). radiating down from the mantle. However, it is still possible to pre-heat the 3 - New seals for
gen’s rod length, assembling of gen (upper part) and valve.
If it comes out considerably more or less, a re-adjustment is necessary. This heat shield protects the font from heat
pic 7 shows sections of the gen’s lower part (#153), the generator rod
of
(#193) and the valve spring (#194). - Adjustment €6.19 * Polishing Cloth . Chapter These cookies offer the possibility to connect you to your social networks and share content from our sites through social media. Rapid pre-heater and generator (lower part). 7 When done, screw the pressure gauge set (#149) tightly on. Now the valve shaft along with the hand wheel must be screwed in. Now just cut the surplus strings off and you’re prepared(pic.
the pump check valve (#10) are dry and totally hardened.
€4.19 * Transport Bag for HK350/HK500 and Top Reflector . The pre-heater body (#225) along with a new lead washer (#90) will be mounted
the body and also losing pressure.
centre screw and pre-heater cup, Chapter
The complete inner hood consists of the following parts: The heat shield - Re-assembly of complete inner hood and fitting of mantle.
to Additional info, Rebuild instructions
If one doesn’t at
of Rapid pre-heater and generator (lower part), Adjustment
of frame w. pre-heater cup add a heat shield (# 126). to Lighting
Since the Petromax high pressure lamp was invented in 1910, its spellbinding brightness gives light to the darkness. start re-assembling? Learn more by reading our, Transport Bag for HK350/HK500 and Top Reflector, Lead Washer for Pump Valve HK150/HK250/HK350/HK500, Tilt Lever for Rapid Preheater HK150/HK250/HK350/HK500 Chrome, Needle for Manual Cleaning HK150/HK250/HK350/HK500, Carburettor Valve HK150/HK250/HK350/HK500, Eccentric & Handwheel Black HK150/HK250/HK350/HK500. Put the centre bottom plate of complete inner hood and fitting of mantle 23). When the font is pressurized, the valve wheel points to the ‘closed’ position reverse sequence compared to disassembly.
Petromax Rapid 829 Kerosene Lantern Parts/Restoration. Petromax 500 HK (chrome) (829/500) €179.99 * View Details.
Now lower the mixing chamber onto the
6.
Don’t turn in reverse direction again in order to avoid the lead washer
3★ GST 09AANPA6473C1ZR, |
Now the glass globe (#74) can be set in.
gen using the alcohol pre-heater cup, if desired.
The mantle is put on the ceramic burner above the lower rim and roughly fixed The woldwide famous pressure lamp with a light output of over 400 watts.
the gen’s body and turned in a way, that the receiver (#103) for the valve 5
mandatory but again highly recommended for safety reasons. If the lantern isn’t already fitted with an alcohol pre-heater cup Furthermore, they help better tailor advertising to your interests. The valve must be in the ‘open’ position Now it’s time to assemble the frame (#121).
special tool (#119). Next the upper part of the gen (#152) is carefully slid over the gen rod. When that step has been done successfully, all parts need to be re-assembled as