Did you frame the sides of the hog panels?

I ripped these pieces in half to obtain 2×2’s for the panel vertical pieces. Make sure the distance between the posts is slightly longer than the panels. I am getting ready to do a version of this around an orchard using 8 ft posts and 3 strands of cable above the hog panels to keep dear out. But when the land level alters much, you'll have to cut the fencing at several spots—brace those places—and start running it anew to adjust to the angle changes.

At MOTHER EARTH NEWS for 50 years and counting, we are dedicated to conserving our planet's natural resources while helping you conserve your financial resources.

Thanks for all of the information and I hope you have it in you to answer one more question! (Just don't let it get grounded anywhere.)

And remember, with this and every other gate, the end posts at the passageway will have to be braced to support the rest of the fence. You can add a temporary "dummy" brace outside the fence line at corners if you want, or just try to pull from around the bend. Dig it on the shrinking moon, and you won't have enough.". . A lot of people use woven, or net, wire (Fig.

You'll want to tighten up woven wire just as much as you would barbed line.

Well, to keep things interesting, we have to bring up one last complicating factor: There are four common tools used for tightening up fence lines: a crowbar (which is not the best device for the job, because it can only grab the wire at its barbs) . 15). but it often doesn't work so well on sheep. Looks great! It's work, but it isn't complicated. With that, you can build a professional looking fence – like this 6 foot privacy fence with a slatted top panel and a warm wood stain finish. Caryl – Here’s how I built the panels. Yes they are treated posts and I buried them about 18 inches. diameter (4 gauge wire). 3).

Now that subject brings to mind the easy way to do minor—short-term—retightening on a drooping fence: Just grab a wire in the claws of a horizontally held hammer and straighten that tool up. I particularly interested in seeing how you adjusted the panels to fit snugly between the 4×4’s. If you've got a really sandy soil, you might need to pack each hole with gravel for it to hold a post firmly . Ben, that’s the beauty of using good quality treated lumber. 14) will let people through, but not cattle, horses, or—if you construct it snug enough—grown sheep. .

. That's enough line to make a four-strand fence that's 330 feet long. and some form of come-along (Fig. .

Remember, though, this is also the potentially dangerous part of the operation, so put on your sturdy clothes and thick gloves and work carefully. And how long is a long brace? Then hook onto the line with your wire stretcher, pull that strand taut, and hammer a couple of staples in to hold the section in place. They're a tad more difficult. The simplest way to do this is to sink a pole at one corner of the intended enclosure, set another as far away as you can run a straight line of string, and then use that cord to line up the sites for all the posts that go in between . At a certain point, though, you'll save money or trouble by using some other fencing.".

Dear Rick, you said it very well.. "The simplest way to do this is to sink a pole at one corner of the intended enclosure, set another as far away as you can run a straight line of string, and then use that cord to line up the sites for all the posts that go in between . You can use the same tools as you would to stretch the pointy fencing—pulling each horizontal line of the welded wire in the sequence you prefer—or make (or buy) a clamp to pull all the fence tight at once. Rick's got two answers to that one: "My uncle always said if you charged a post from ten feet and it didn't budge, it was in tight enough . You'll want to be sure that the diagonal is a lengthy one. and can seriously injure themselves.).

. Laying out the posts and braces is definitely the most labor- and time-consuming part of the whole operation. You make the two loops, stand the stick in 'em, and fasten the gap-spanning wires.

If working alone, use your body to hold the gripping tool in place. How much did you burry vrs the hight left above the ground? On a 4'-high fence, then, use 6' to 8' diagonals. account?

In this situation, you can build one of the corner units just mentioned or rig a slick-wire X arrangement (see Fig.

However, so many tractor operators have been hurt or killed after an overstretched line snapped that the National Safety Council strongly recommends against this practice.

You'll still have to make some way for people and creatures to get in and out of the enclosure, won't you?

Thanks! We've run six strands in a 48" fence to contain goats, too . Whoops .

Also isn’t all the weight on the 2×2’s.since the 2×4’s aren’t attached to the posts? I just went to a hardware store and bought some large strap hinges available anywhere. Is there a device available that can support a barbed wire to the post, but still allow the barb to slide thru it when you want to re-tension the barb?

Building a new fence using a combination of wood and metal is an excellent way to beautify your backyard.

'cause then you'll get to drive them slightly downward instead of slightly upward. The fact is—if you're not real careful—you can get seriously hurt. 10). That's a big difference (and that price doesn't take into account any barbed line you might add on top of the netting). International Subscribers - Click Here I raised each panel about 4″ from the ground for attachment to the posts and put a top 2×4 piece on each panel after each panel was installed. You may also use the Bill Me option and pay $17.95 for 6 issues. . Building a good barbed wire fence, you see, is not as simple as just putting up a line of poles and then tacking on some wire. We're going to lay out Rick's time-honored fencing methods in detail. When you come to big tree feeders, though, save yourself some aggravation by moving the hole over enough to miss 'em. ("I've done it," Rick confesses.)

I really want to build a similar fence but I’m worried about building the panels and not spacing the posts properly. Tear bark off before stapling so the U-nails'll get a better grip on the wood. . Two or three strands of that—set on insulators fastened to metal or wood posts, or simply wrapped right around store-bought plastic supports—doesn't cost much and is easy to set up. To give you something sturdy to pull against.) We're going to base the rest of this article on the assumption that you'll use one of those handy one-man wire stretchers, as Rick does, so we won't say any more about two-in-a-row supports.

Pre-Fabricated, Gambrel Roof A-Frame Plan, Natural Cold Storage: Fresh Food in Winter, Keeping Crops Cool During Hot Weather: 13 Ways to Beat the Heat, Subscribe Today - Pay Now & Save 64% Off the Cover Price.

Now comes the fun—and tricky—part. Install posts and cut the top rails long enough to span three posts. Secure each wire tip a few inches from its end with a fence staple, then bend the loose end back on itself and staple that in well. Canadian Subscribers - Click Here Tutorial: How to Build a Fence with Pallet Materials. The gate by the mailbox is a little over 3 ft wide. We did have to replace two posts. They had better lumber in the sizes I needed than Lowe’s or Home Depot. or if you're working in muddy ground, you'll probably have to use concrete around the base. ("I figure if the top won't move and the bottom won't move, the post won't move.

Four common tools for tightening up fence lines.

No sir, for a fence to last and keep livestock in their place, it's got to be taut . Rick begins by running his bottom strand, then puts on the top one, and afterwards adds the two middle lines, because he believes this sequence best balances the strains put on his brace posts. and "Hurry up, the animals are out again!"

But can you give us a few guidelines for normal creatures? Register now to get access to ALL current video workshops and prerecorded webinars plus anything new that we add through the end of 2020. . .

Then nail that "winder" stick against the brace, and you're done (Fig. Your job will be easier if you always hammer them short end up . (Otherwise, the tension on the wires will tend to pull them down off their posts.)